C H A P T E R 1 - Sun StorEdge 3000 Family FRUs

C H A P T E R 1

Sun StorEdge 3000 Family FRUs

This document provides instructions for removing and installing field-replaceable units (FRUs) in Sun StorEdge 3120 SCSI arrays, Sun StorEdge 3310 SCSI arrays, and Sun StorEdge 3510 FC arrays.

Instructions are also included for FRUs which are common to all three arrays. These FRU components can be replaced by customers or by Sun service representatives.

This chapter covers the following topics:

Available FRUs

Static Electricity Precautions

Removal and installation instructions are provided for the following FRUs:

Disk drives

Power and fan modules

Card modules

Special-Use FRUs, such as batteries

1.1 Available FRUs

Most FRUs are hot-swappable except a few modules which are hot-serviceable. Hot-serviceable means that the module can be replaced while the RAID product and hosts are powered up but the connected hosts must be inactive.

Caution - Please follow the FRU procedures carefully to ensure successful FRU replacement.

The following tables list the FRUs that are currently available. For additional FRUs and X-options, consult your sales representative or the latest Release Notes for Sun StorEdge 3000 Family products on Sun web sites.


FRU Model Number	Description
F370-6195-xx	1U JBOD, LVD, Chassis + I/O board with SAF-TE
F370-6193-xx	AC power supply and fan module, 1U
F370-6192-xx	DC power supply and fan module, 1U
F370-5405-xx	Cable, LVD, 1-foot, jumper
F370-5528-xx	Cable, LVD, 1.5-foot, expansion
F540-6054-xx	Drive module, 36 GB LVD, 10K RPM
F540-6055-xx	Drive module, 36 GB LVD, 15K RPM
F540-6056-xx	Drive module, 73 GB LVD, 10K RPM
F540-6057-xx	Drive module, 73 GB LVD, 15K RPM
F540-6058-xx	Drive module, 146 GB LVD, 10K RPM
XTA-3000-AMBS	Air management blank sled

Caution - You can mix capacity in the same chassis, but not spindle speed (RPMs) on the same SCSI bus. For instance, you can use 36 Gbyte and 73 Gbyte drives with no performance problems if both are 10K RPM drives. Violating this configuration guideline leads to poor performance.


FRU Model Number	Description
F370-5394-xx	Event monitoring unit
F370-5396-xx	I/O module, LVD, expansion unit or JBOD
F370-5397-xx	I/O module, LVD, RAID
F370-5403-xx	Controller module, 512 memory, battery, 2U LVD
F370-5399-xx	Terminator module
F540-5522-xx	Drive module, 36GB LVD, 10K RPM
F540-5563-xx	Drive module, 73GB LVD, 10K RPM
F370-5398xxAC	AC power and fan module, 2U
F370-5527-xxDC	DC power and fan module, 2U
F370-5533-xx	Battery, LVD
F370-5405-xx	Cable, LVD, 1-foot, jumper
F370-5528-xx	Cable, LVD, 1.5-foot, expansion
F370-5393-xx	Box, 2U, JBOD, LVD
F370-5524-xx	Box, 2U, RAID, LVD
XTA-3310-DC-KIT	Power and fan module, 2U, DC


FRU Model Number	Description
F370-5535-xx	Box, 2U, FC, Chassis + Backplane (RAID/JBOD)
F370-5545-xx	Battery, FC, 2U
F370-5540-xx	Cable, FC, 1.5 FT, expansion
F370-5537-xx	I/O w/SES and RAID Controller FC, 1GB memory, battery, 2U
F370-5538-xx	I/O w/SES, JBOD FC, 2U
F370-5398-xx	AC power supply/fan module, 2U
XTA-3310-DC-Kit	DC power supply/fan module, 2U
XTA-3510-36GB-15K	Drive module, 36GB FC, 15KRPM
XTA-3510-73GB-10K	Drive module, 73GB FC, 10KRPM
XTA-3510-146GB-10K	Drive module, 146GB FC, 10KRPM
XTA-3000-AMBS	Air Management Sled
XSFP-SW-2GB	SFP, 2G, SW 850NM, FC, TRANS
XSFP-LW-2GB	SFP, 2G, LW 1310NM, FC, TRANS

1.2 Static Electricity Precautions

Follow these steps to prevent damaging the FRUs:

Remove plastic, vinyl, and foam from the work area.

Before handling a FRU, discharge any static electricity by touching a ground surface.

Wear an antistatic wrist strip.

Do not remove a FRU from its antistatic protective bag until you are ready to install it.

When removing a FRU from the RAID product, immediately place it in an antistatic bag and in antistatic packaging.

Handle a FRU only by its edges, and avoid touching the circuitry.

Do not slide a FRU over any surface.

Limit body movement (which builds up static electricity) during FRU installation.